liviu2004 135 Posted April 12, 2014 Share Posted April 12, 2014 Să vă explic / arăt cum am activat martorul în bord pentru centură șofer. Ce avem nevoie: - să nu punem contactul sub nici o formă, pentru că ar putea airbagul să înregistreze eroare când se desface mufa de sub scaun. - în primul rând de un bec în bord, vedeți aici în această poză, la poziția Gurtwarner, eu am pus un LED alb, atenție la polaritate, eventual trebuie sucit 180 de grade: - apoi trebuie o centură cu senzor pentru partea șoferului, eu am găsit una noua pe ebay uk, cod GM 9201088, are două mufe, una albastră și una verde (poza e doar pentru exemplu, e de la pasager): - eu am fost puțin norocos și am avut cablajul tras în mașină, până la mufa de sub scaun, mufa cu 2 pini din partea dreaptă spre centru: - ca să pot scoate centura veche, a trebuit demontat scaunul, sunt 4 șuruburi cu cap torx, nimic spectaculos; - la final în bord arată cam așa: Nu e nevoie de vreo activare, la mine a mers din prima. Bine, am nenorocit becul pentru vreo câteva luni, când am modificat code index la BCM cu opcom. Numai cu tech2 și-a mai revenit becul. Și un mic film cum lucrează bordul: Enjoy și vă aștept cu întrebări. Quote Link to post Share on other sites
catastefan 4 Posted April 12, 2014 Share Posted April 12, 2014 Felicitari pentru tutorial si tine-o tot asa. liviu2004 1 Quote Link to post Share on other sites
liviu2004 135 Posted November 23, 2014 Author Share Posted November 23, 2014 beverlytourer, here are the pictures: - wiring diagram, as you can see, one wire to ground and one to BCM plug - picture of the plug under the seat, circle is for the wiring on pins 11, 12, where the seat belt sensor is located. If you make a bridge between 11-12, dashboard light should go ON. but do not forget about the airbag light, should not put contact ON with plug OUT. Quote Link to post Share on other sites
taedla01 12 Posted August 17, 2017 Share Posted August 17, 2017 Hello everyone! Remember to enable seat belt state with Tech2/MDI in instrument cluster (IPC) if you want to ear the buzzer sound while car moves and seat belt circuit is open. (Tested on Corsa-C Z13DT 2006). Regards from Spain! Dario. liviu2004 1 Quote Link to post Share on other sites
liviu2004 135 Posted August 17, 2017 Author Share Posted August 17, 2017 Dario, I could never make the buzzer work. Can you please share your dash part number or alpha code, code index and country selection in dash? Quote Link to post Share on other sites
taedla01 12 Posted August 17, 2017 Share Posted August 17, 2017 Hi liviu! Sure I do it! Please let me to connect opcom and take info. Then I put an screenshot. I will upload a video too. Thank you for sharing your knowledge! Cheers, Dario. liviu2004 1 Quote Link to post Share on other sites
taedla01 12 Posted August 17, 2017 Share Posted August 17, 2017 Hello everyone! Liviu, here we go! This is opcom main report: And here you can see how the light blinks when you turn ignition on and while seat belt is not attached. The buzzer start to make noise when you reach about 20 km/h: IMG_3967.MOV Cheers, Dario. Ericson and liviu2004 2 Quote Link to post Share on other sites
Ericson 0 Posted May 22, 2019 Share Posted May 22, 2019 Olá os vídeos como configurar aviso de cinto de segurança não é mais disponível, pode fazer o upload novamente por favor Quote Link to post Share on other sites
Ericson 0 Posted May 23, 2019 Share Posted May 23, 2019 On 8/17/2017 at 4:23 PM, taedla01 said: Hi liviu! Sure I do it! Please let me to connect opcom and take info. Then I put an screenshot. I will upload a video too. Thank you for sharing your knowledge! Cheers, Dario. On 8/17/2017 at 8:52 AM, taedla01 said: Hello everyone! Remember to enable seat belt state with Tech2/MDI in instrument cluster (IPC) if you want to ear the buzzer sound while car moves and seat belt circuit is open. (Tested on Corsa-C Z13DT 2006). Regards from Spain! Dario. Hi, can you show how to do this process to set up the buzzer ? Quote Link to post Share on other sites
r19 0 Posted October 26, 2020 Share Posted October 26, 2020 On 23/11/2014 at 15:28, liviu2004 said: beverlytourer, aqui estão as fotos: - diagrama de fiação, como você pode ver, um fio para o terra e um para o plugue BCM - imagem do plugue sob o assento, o círculo é para a fiação nos pinos 11, 12, onde o sensor do cinto de segurança está localizado. Se você fizer uma ponte entre 11-12, a luz do painel deve acender. mas não se esqueça da luz do airbag, não deve colocar o contato LIGADO com o plug OUT. what is the bcm pin? seems to be the 23 my car has no installation Quote Link to post Share on other sites
liviu2004 135 Posted October 26, 2020 Author Share Posted October 26, 2020 Yes, seems to be plug X45 pin 23. You need donor auto pin, I noticed pin format differ with at least 2 variants depending on build year. With the buzzer, either will work oem or will not work at all. Older dash seem not to have the buzzer function and newer dash have it oem, like I have now a Meriva 2008 dash. Quote Link to post Share on other sites
r19 0 Posted October 26, 2020 Share Posted October 26, 2020 5 hours ago, liviu2004 said: Sim, parece ser plug X45 pino 23. Você precisa de pino automático doador, notei que o formato do pino difere com pelo menos 2 variantes dependendo do ano de construção. Com a campainha, ou funcionará oem ou não funcionará de todo. O painel mais antigo parece não ter a função de campainha e o painel mais recente tem oem, como eu tenho agora um painel Meriva 2008. Yes thanks I have...I already installed the cruise control in the car and they are the same at the exit and which and where will the terminal end? thank you from Portugal Quote Link to post Share on other sites
liviu2004 135 Posted October 26, 2020 Author Share Posted October 26, 2020 In don't understand what you need. Aren't the pictures from first post not clear? Plug under the seat? Pirotechnics with sensor attached to chair? Quote Link to post Share on other sites
r19 0 Posted October 26, 2020 Share Posted October 26, 2020 10 minutes ago, liviu2004 said: In don't understand what you need. Aren't the pictures from first post not clear? Plug under the seat? Pirotechnics with sensor attached to chair? what is the bcm pin shown in the photo Quote Link to post Share on other sites
liviu2004 135 Posted October 26, 2020 Author Share Posted October 26, 2020 Do you ask how the pin looks like? I don’t know anymore, it’s been 6 years since I’ve done the job. And I ain’t gonna open bcm to make a picture. Quote Link to post Share on other sites
r19 0 Posted December 28, 2020 Share Posted December 28, 2020 already works but the light is always on and I have no audible warning Quote Link to post Share on other sites
liviu2004 135 Posted December 29, 2020 Author Share Posted December 29, 2020 (edited) Hi, audible warning works on Meriva late years dash, never got it going in Corsa nor Tigra dash. If light always on, something wrong in wiring or BCM config, afraid opcom can't fix it, only tech2, been there done that. Can't remember if mine was completely off once I played with opcom, well ... Edited December 29, 2020 by liviu2004 Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.